Entries 1 to 156. Total of 156 entries found.
No.Description 
1Adapter, stainless steel M16x1 (internal) on M16x1 (external) for metal tubing system 
2Agitator coupling type CF with torsion spring, stainless steel Clamping range-D= 5-9 mm 
3Agitator coupling type CV with metal bellows, stainless steel Clamping range-D= 5-9 mm 
4Agitator coupling type RV with metal bellows, stainless steel Clamping range-D= 6-8 mm 
5Bearing ring stirr closure w/o glass part, Ø 16mm 
6Bottom carrier ring stainless steel tube 3/4" Oktagon DN 300, 2xbeam 
7Bracket ring connector DN 25 plastic 
8Bracket ring connector DN 40 plastic 
9Carrier mobile stainless steel, with stirrer support, closed version DN 300 
10Carrier mobile, open form stainless steel tube V2A, with connecting element, 500x500x900mm, without rolls 
11Closure, clamping range 2...5 mm Ø straight feedthrough with gasket set vacuum-tight, with ground joint NS 14/23 
12Closure, clamping range 5...10 mm Ø with gasket set DS 02, with conical ground joint 29/32 
13Closure, clamping range 5...11 mm Ø conical ground joint 29/32, with plastic cap 
14Connetor DN 300 stainless steel 
15Contact cable 1,5m length for connection thermosensor Thermostat PI-C30P 
16Coupling for stirrer type RF with torsion flute, stailess steel tensioning range= 6-8 mm 
17Cross sleeve 30 mm, aluminium 
18Disc for flange vessel DN150, Mh 29, 2xSh 29, Sh 14 
19Disc for flange vessel DN150, Mh 29, 2xSh 29, Sh 29 
20Disc for flange vessel DN200, Mh 29, 2xSh 29, Sh 29 
21Double coupling, stainless steel to connect 2 glass flanges Nominal width DN 15 
22Double coupling, VA, for two glass flanges DN 25 
23Drain valve "K" short design, complete without glass part 
24Dropping funnel 500 ml, NS 29 grad. with hollow chick and clamping fuse 
25Dynamic Seal for Stirrers 19 with Double Seal in PTFE, for mandrel 10 mm 
26Dynamic Seal for Stirrers 29/32 with Double Seal in PTFE, for mandrel 16 mm 
27Dynamic Seal for Stirrers 29/32 with Double Seal in PTFE, for mandrel 10 mm 
28Dynamic Seal for Stirrers 45/40 with Double Seal in PTFE, for mandrel 8 mm 
29Dynamic Seal for Stirrers 45/40 with Double Seal in PTFE, for mandrel 16 mm 
30Dynamic Seal for Stirrers 45/40 with Double Seal in PTFE, for mandrel 10 mm 
31Dynamic seal for stirrers with plastic cap 10 mm, NS 29/32 
32Filter unit DN 50 
33Flat cover for shaving Pipes DN 120 
34flat flange cover DN60s Mh NS 29/32 Sh 2x NS 14/23 angled ***DIN flange 12214*** 
35Flat flange gasket in PTFE, DN150 
36Flat flange lids 
37Flat flange lids NW 120 NS 29, 2xNS 29 angled, 1xNS 14 parallel 
38Flat flange seal with grooves PTFE, 25 DN 
39Flat flange vessel 1000ml DN 120, type ADAV: cyl. form, thermostatic with bottom outlet valve 
40Flat flange vessel 250ml type ADAV, DN60, cylindr. form, thermostatic with bottom outlet valve 
41Flat ground connector DN 200 stainless steel, with suspension device for tube frame 
42Flat ground connector DN 200s stainless steel, with suspension device for tube frame 
43Flat ground flange reaction vessels 3000 ml 
44Flat ground flange reaction vessels, jacketed 
45Flat ground flange reaction vessels, unjacketed 
46flat ground flange rection vessel 2000ml DN 120,flask/term. jacket without socket 
47Flat ground gasket PTFE, for DN 100 
48Flat lid for ground glass vessels NW150, Mh NS 29/32, 2xSh 29/32s, 1 x NS 29/32g 
49Flat-gasket DN150 with Graphite for temperatures up to 400°C 
50Fork clamp for NS 24 
51Gasket set for closure DBGM, type A clamping range 5-11 mm with NSK 29/32 
52Gasket Set for closure Ø 2-5mm, DS 01 complete 
53Gasket set, PTFE for shaft 10 mm, order no: 2 lip seals and O-ring 
54Gasket set, PTFE for shaft 16 mm, order no: 2 lip seals and O-ring 
55Gasket set, PTFE/graphite for shaft 10 mm, order no: 2 lip seals and O-ring 
56glass cover for reactor 
57Glass part for ring stirring closure for 10 mm waces-Ø, with NS 29/32 
58Glass part for sliding ring stirrer closure for 10 mm shaft Ø, with NS 45/40 
59Glass part for sliding ring stirrer closure for 16 mm shaft Ø, with NS 45/40 
60Ground joint clips for sleeve connections, wire, Chrome-nickel steel 
61Guide pressure sleeve, PTFE glass fibre reinforced for shaft 10 mm diam. 
62Guide pressure sleeve, PTFE glass fibre reinforced for shaft 14/16 mm diam. 
63Guiding pressure sleeve, PTFE Glass fiber reinforced For shaft 8 mm Drm. 
64Holding ring for "Vario-Crip" DN 100 
65HWS-Covers DN 60 MH NS 19/26, SH 3 x NS 14,4 HWS 
66HWS-flat flange gasket in ePTFE, DN 15 
67HWS-Flat range gasket, PTFE with insert, DN 120 
68Mechanical agitator seal Body and agitator shaft holder PEEK Seal rings/O-rings FKM/FKM 
69Metal adapter for metal hose DN 15 Thread M30 x 1.5 
70Metal adapter for NW 25 thread M 16 
71Metal tubing length 1,0 m thread connection M 16 
72Metal tubing length 1,5 m thread connection M 16 
73Metal tubing length 2,0 m thread connection M 16 
74Metal tubing length 3.0 m threaded connection M 16 
75Microflon blue seal for DN15p 
76O-ring DN 120 FKM for flat flange according to DIN 12214 
77O-ring DN 150 for plane ground sections incl. groove, silicone 
78O-ring for flat flange vessels DN 60s incl. nut, system "s", silicone, FEP 
79O-ring NW 100 S FKM 
80O-ring NW 100 S made of silicone FEP-coated with groove 
81O-Ring NW 100 S Silicone 
82O-ring NW 120 S made of silicone, FEP coated 
83O-ring NW 150 S made of silicone FEP-coated 
84O-ring sealing for NW 120 S made of silicone, DIN 12.214 
85O-ring, silicone/FEP-coated for Rotulex 13/5 
86O-sealing DN 200 glueless FEP-coated 
87Over pressure valve NSK 29/32 0,5 bar 
88Pin a spanner stainless steel, DN 25 
89Pl. lid FI/DIN NW 100 H 125, MH NS 29/32 SH 4x NS 29/32 oblique 
90Pl. reaction vessel 2000ml Type ADAV, cylindrical, with heating jacket and bottom drain valve 
91Pl. reaction vessel 500 ml 
92Pl. reaction vessel 500 ml 
93Pl.-reaction vessel 20000ml 2 x DN 15 p, flask/temp. 
94Pl.-reaction vessel 30000ml DN 300, flask/temp. 
95Pl.-reactions vessel 50000ml DN 300, flask/temp. 
96Pl.-reakcion vessel 40000ml DN 300, flask/temp. 
97Plane ground universal connector NW 150 Cervical spine flange with stand rods 
98Pressure screw made of PTFE for shafts 14/16 mm glass fibre reinforced 
99Pressure screw made of PTFE for shafts 8/10 mm glass fibre reinforced 
100PS lid DN150 Mh NS 45/40 Sh 2x NS 29/32 straight 2x NS 29/32 angled ***HWS flange system*** 
101PS lid DN200 Mh NS 29/32 
102PS Vessel 2000ml ADAV DN150, drain valve "T" 10mm, 
103PS vessel type ADAV DN100, 1000 ml Drain valve "H" 20mm Ø, drain thread GL32, 2x HM DN15p, HWS flange system 
104PTFE collar sealing DN 25 
105PTFE comb seal DN 100 
106PTFE comb seal DN 120 
107PTFE seal for DN 100 with groove centring 
108PTFE-collar sealing DN 40 
109PTFE-comb sealing DN 300 
110PTFE-Flat Flange Seal DN 15, with Grooves 
111PTFE-flat sealing DN 300 
112Quick fixing "Vario Grip" (nichrome) DBGM, "HWS" 
113Quick fixing "Vario Grip" (nichrome) DBGM, DN 100, "s" 
114Quick fixing "Vario Grip" stainless steel, complete profile ring made of PP, NW 100, "HWS" 
115Quick release clamp, nichrome for "s" system, DN 100 
116Quick release clamp, nichrome for "s" system, DN 150 
117Quick release made of nichrome for NW 100s, (flange according to DIN 12.214) with 2 tripod bars Ø 13 mm 
118reaction vessel accessories Modell T 10mm 
119Seal for flat flange vessel 
120Seal kit, PTFE for wave 8 mm, 3-parted 
121Seal kit, PTFE/Graphit for wave 8 mm, 3-parted 
122Seal kit, PTFE/graphite for shaft 16 mm, 2x lip seals and 2x O-ring 
123Sealing ring DN 100 FKM 
124Sealing, silicone/PTFE 
125Sealing, silicone/PTFE 
126Sliding ring stirrer seal NS 29, Ø 10 mm 
127Sliding ring stirrer seal NS 29/32, Ø 10 mm seal rings FKM, O-rings Perfluor / FFKM 
128Sliding ring stirrer seal NS 45, Ø 10mm 
129Sliding ring stirrer seal NS 45, Ø 16 mm 
130Solid matter dosing feeder DOSINI 250 ml, GL 32, NS 29, with electrical PTFE-charging screw 
131Square seal made of FKM for shaft dia. 10 mm 
132Stirr closure "Dyna" with cone NS 29/32 for wave-dia. 10 mm with radial needle bearing 
133Stirr coupler Type RV/E with stainless steel folded bag, range-D: 12-14 mm 
134Stirr cover NS 29/32 with double PTFE-lip seal, for wave 8 mm 
135Stirrer coupling type EK with stainless steel gimbal Shank 14mm 
136Stirrer coupling type EK with stainless steel gimbal, with GL 14, for stirrer KPG 16 
137stirrer coupling with stainless steel double "Kardan" for stirrer stud diam 16 mm 
138Stirrer Seal 29/32 with GL 14 for Gas Inlet, for mandrel 10 mm 
139Stirrer Seal 45/40 with GL 14 for Gas Inlet, for mandrel 10 mm 
140Support ring DN 150/200 
141Supporting Device DN 100 for tube 27 mm 
142Supporting device DN 150 for tube 27 mm 
143Supporting device for carrying frames, (tube Ø 13 mm) 
144Supporting ring 
145Supporting ring DN 150 Polyester, with support rod 
146Surface grinding connector NW 100 HWS-flange w. support rods 
147Tray for VD 03 stainless steel 
148Tube adapter for rod 16 mm 
149Tube adapter for rod 20 mm 
150Tube Coupling GL18 
151Tube olive GL 18 curved 
152Tubing adapters for heating and cooling connection 
153Universal connector stainless steel DN 200s for carrying frame tube D 13 mm ***DIN flange system 12214*** 
154Valve insert complete (without glass parts), PTFE 
155Valve, pneumatic, type PT stroke length adjustable 
156Valve, pneumatic, type PT/P stroke length adjustable